Retsch AS 200 control - natural frequency Manuel d'utilisateur

Operating Instructions for Sieving Machine Type AS 200 control Retsch GmbH 42781 Haan, Retsch-Allee 1-5, 2/7/2012 0002

Retsch GmbH 10 Transport and installation Packing Packing has been adapted to the transport method and conforms to generally

Retsch GmbH 11 Parameters for the installation location Ambient temperature: 5°C bis 40°C If the ambient temperature is exceeded or

Retsch GmbH 12 Operation Operating elements and operation A Cold apparatus plug combination C Fuse compartment with 2 glass fuse

Retsch GmbH 13 Insertion and clamping the analytical sieves The AS 200 control is suitable for analytical sieves of outside diameter

Retsch GmbH 14 Clamping with the clamping unit - comfort H I K I K Screw support rod H into the sieve plate

Retsch GmbH 15 Operation of the AS 200 control Switching on / off E The main switch E is located on the front left-hand side of t

Retsch GmbH 16 Adjusting the time 12 13 14 On switching on the AS 200 control the sieving time is undetermined = 2 bars in displ

Retsch GmbH 17 Amplitude in „mm“ In display 5, labelled with amplitude mm/g, twice the amplitude is shown as measured value. We

Retsch GmbH 18 Operating hours display 3 9 If the buttons described below are pressed, the complete running time of the machine

Retsch GmbH 19 Quantities of material to be sieved The sieve set is made up of the collecting bottom and the analytical sieve

Retsch GmbH 2 Notes on these operating instructions ... 3 Warnings ...

Retsch GmbH 20 Wet sieving In most cases dry sieving is possible. However, with some materials the adhesive forces betw

Retsch GmbH 21 The water quantity added should always be dosed in such a way that the sieve surface is only just wetted. Use vent r

Retsch GmbH 22 Information on the sieve bottom acceleration mode The AS 200 control is a throwing-type sieving machine which gives yo

Retsch GmbH 23 Acceleration guide values In the technical literature* on plant engineering sieve bottom acceleration in „g“

Retsch GmbH 24 Retsch Analytical sieves The highest precision for exact results The accuracy and the reliability of the analysis resu

Retsch GmbH 25 Working instructions Sieving aids When dealing with material that is difficult to separate, we recommend the

Retsch GmbH 26 EasySieve Control, evaluation, documentation. EasySieve , the software package from RETSCH for grain size analys

Retsch GmbH 27 General Cleaning For thorough, gentle and time-saving cleaning of your analytical sieves we recommend Retsch ul

Retsch GmbH 28 Wearing parts Item11 / Art. No. 03.243.0044 1x rubber ring Item 37 / Art. No. 05.699.0052 2x fuse cartridges

Retsch GmbH 29 Authorized person for the compilation of technical documents: J. Bunke (technical documentation) The following record

Retsch GmbH 3 Notes on these operating instructions These operating instructions for the analytical sieving machine type AS

Retsch GmbH 30

Retsch GmbH 31

Retsch GmbH 32 Copyright ® Copyright by Retsch GmbH Haan, Retsch-Allee 1-5 D-42781 Haan Federal Republic of Germany

Retsch GmbH 4 Safety Target group: All persons concerned with the machine in any way. The AS200 is a modern, highly efficient produ

Retsch GmbH 5 Summary of safety instructions – part 1 Safety instructions We exclude claims for damages in any form for damage to p

Retsch GmbH 6 Summary of safety regulations – part 2 Wet sieving Never operate your AS 200 control directly in water. Danger throug

Retsch GmbH 7 Confirmation I have read and taken note of the sections – preliminary comments and safety ________________________

Retsch GmbH 8 Technical data Machine type designation: AS 200 control Use according to the intended purpose The AS 200 control h

Retsch GmbH 9 Emissions Noise characteristic values: Noise measurement is carried out according to DIN 45636-031-01-KL3. The noise